RETIRED ›
This product is no longer available. Some accessories, replacement parts, or services may still be available.
A205 CWS Sensor to PC Interface
Services Available
Repair Yes
Free Support Yes

Overview

The A205 CWS-to-PC Interface supports communication between wireless sensors and a computer. The A205 is necessary for configuring wireless sensors prior to deployment and is also useful for testing and troubleshooting them.

Read More

Technical Description

The A205 has a four-pin connector that attaches to the four-pin male connector located behind the battery pack of a CWS sensor. It connects with the computer via a USB port. When connected to a computer's USB port, the A205 supplies power to the wireless sensor.

 

 

Images

Specifications

Connectors
  • Type B USB female
  • Four-pin female
Dimensions 13.97 x 10.16 x 3.81 cm (5.5 x 4.0 x 1.5 in.)
Weight 68.04 g (0.15 lb)

Compatibility

The A205 is compatible with all of our CWS220-series Infrared Radiometers, CWS655-series Water Content Reflectometers, and CWS900-series Configurable Wireless Sensor Interfaces.

Downloads

A205 CWS Interface USB Driver v.2.08.28 (1.64 MB) 05-03-2013

A205 USB Drivers for the Windows operating system. 32 and 64 bit support for Windows 8, Windows 7, Windows Vista and Windows XP.

Note: Drivers should be loaded before plugging the A205 into the computer.

Listed Under

Common Accessory for the following products:

FAQs for

Number of FAQs related to A205: 6

Expand AllCollapse All

  1. To use the A205 with a wireless sensor interface and a wireless sensor base, is direct line of sight necessary?

    No. The A205 is an interface for communicating directly between a computer and a wireless sensor.  It has no impact on the radio communication between the wireless sensor and the wireless sensor base, so line of sight doesn’t matter.

  2. Can the A205 be used to determine whether there are communication issues between the wireless sensor and the wireless sensor base?

    No. The A205 is for communication with a single sensor only and cannot access any information related to the wireless sensor network. Use the CRBasic CWB100Diagnostics instruction in the data logger program to collect information on the wireless sensor network performance.

  3. Can the A205 be used to determine whether a wireless sensor is a repeater in a wireless sensor network?

    No. Use the CRBasic CWB100Routes() instruction in the data logger program to collect information as to which sensors are repeaters.

  4. Can the A205 be used to determine signal strength (RSSI) of a wireless sensor?

    No. Use the CRBasic CWB100RSSI() instruction in the data logger program to measure and record wireless sensor signal strength.

  5. Is it necessary to purchase an A205 CWS Sensor-to-PC Interface for use with a CWS655, CWS220, or CWS900?

    An A205 is required to write the radio address of the wireless base station to the wireless sensor firmware so that the sensor will respond to polling from the base station. This is done using the Device Configuration Utility software. The A205 is also useful for connecting a computer directly to the CWS655, CWS220, or CWS900 for diagnosis, changing the base station radio address, uploading new firmware, and verifying sensor functionality. It is only necessary to purchase one A205—unless multiple users with multiple computers need to perform these tasks.

  6. What is needed to connect a sensor that is compatible with wireless sensor interfaces to a CR800, CR1000, or CR3000 in a wireless network?

    To incorporate a sensor that is compatible with wireless sensor interfaces into a wireless network, a CWS900-series wireless sensor interface is needed, as well as an A205 CWS-to-PC interface to configure it. 

Visit the FAQ Library

Privacy Policy Update

We've updated our privacy policy.  Learn More

Cookie Consent

Update your cookie preferences.  Update Cookie Preferences